3m interconnect solutions http://www.3m.com/interconnects/ 3m is a trademark of 3m company. for technical, sales or ordering information call 800-225-5373 3m ? 4-wall, tripolarized header .050 .100 latch/ejector, right angle, 4 rows of solder tails 810 series physical electrical environmental insulator material: high temperature plastic (lcp) flammability: ul 94v-0 color: black (rb plating only) or natural contact material: copper alloy plating underplating: 100 ? [ 2.54 m ] nickel wiping area: 30 ? [ 0.76 m ] gold solder tails: see ordering information terminal finish indicator: e3 (ref jesd97) marking: 3m logo, part number and orientation triangle current rating: 0.5 a insulation resistance: > 1 10 9 at 500 v dc withstanding voltage: 500 v rms at sea level operating temperature rating: -55 c to +105 c process rating: maximum 260 c (per j-std-020c) moisture sensitivity level: 1 (profile per j-std-020c) ts-0334-17 sheet 1 of 3 ? tripolarization to mating socket ? 50 mil 100 mil halves the connector length ? latch and eject for rugged high performance applications ? two-row tail design saves board space ? high temperature plastic ? four-wall shroud provides contact protection ? contacts: 20, 26, 36, 40, 50, 60, 68, 80 and 100 ? see regulatory informatio n appendix (ria) for chemical compliance information date modified: march 27, 2007 ul file no.: e68080
3m interconnect solutions http://www.3m.com/interconnects/ 3m is a trademark of 3m company. for technical, sales or ordering information call 800-225-5373 3m ? 4-wall, tripolarized header .050 .100 latch/ejector, right angle, 4 rows of solder tails 810 series 81xxx-mx0203-xx .0 .00 .000 inch .1 .01 .005 [ ] dim ensions for reference onl y tolerance unless n oted [mm] inch ordering information notes: 1. this polarization bump does no t exist on the 20 position header. 2. recommended to be mated to the .050 x .100 820 series wiremount socket. a b c .015 x ..015 [0.38] x [0.38] see note 1 position 2 .050 typ [1.27] .015 x ..015 [0.38] x [0.38] position 1 .092 [2.34] .100 ref [2.54] .310 [7.87] ejector/latch system: 0 = none 5 = with short ejectors installed 6 = with long ejector latches installed contact quantity (see table 1) pth right angle header, 4 rows of solder tails ts-0334-17 sheet 2 of 3 position 1 orientation triangle .440 .010 [11.18] .620 ref [15.75] d .165 .010 [4.19] short latch long latch 2x ? .116 [2.95] .122 .010 [3.10] .015 [0.38] .405 [10.29] .828 ref [21.03] .140 .010 [3.56] .265 [6.73] .075 [1.90] .120 ref [3.05] .378 [9.60] .020 [0.51] .107 .010 [2.72] .098 .010 [2.49] .083 .010 [2.11] ejector latch long 3505-28 (natural) 3505-28b (black) short 3505-29 (natural) 3505-29b (black) plating suffix: blank = tin lead tails (ria e3 & c2 apply) rb = matte tin tails (ria e1 and c1 apply) abc d short ( ref. ) d long (ref.) 020 1.060 0.722 0.500 1.671 1.842 [26.92] [18.34] [12.70] [42.44] [46.79] 026 1.210 0.872 0.650 1.821 1.992 [30.73] [22.15] [16.51] [46.25] [50.60] 036 1.460 1.122 0.900 2.071 2.242 [37.08] [28.50] [22.86] [52.60] [56.95] 040 1.560 1.222 1.000 2.171 2.342 [39.62] [31.04] [25.40] [55.14] [59.49] 050 1.810 1.472 1.250 2.421 2.592 [45.97] [37.39] [31.75] [61.49] [65.84] 060 2.060 1.722 1.500 2.671 2.842 [52.32] [43.74] [38.10] [67.84] [72.19] 068 2.260 1.922 1.700 2.871 3.042 [57.40] [48.82] [43.18] [72.92] [77.27] 080 2.560 2.222 2.000 3.171 3.342 [65.02] [56.44] [50.80] [80.54] [84.89] 100 3.060 2.722 2.500 3.671 3.842 [77.72] [69.14] [63.50] [93.24] [97.59] table 1 contact quantity dimensions 1.05 [2.67]
3m interconnect solutions http://www.3m.com/interconnects/ 3m is a trademark of 3m company. for technical, sales or ordering information call 800-225-5373 3m ? 4-wall, tripolarized header .050 .100 latch/ejector, right angle, 4 rows of solder tails 810 series table 2 ejector latches dimension e min no .575 [14.6] short .885 [22.48] long 1.010 [25.6] ts-0334-17 sheet 3 of 3 note: 1. in order to facilitate flow soldering, it is recommended that ejector latches be installed after the soldering process. recommended mounting hole pattern for odd number of contacts/row (shown for mounting side of pc board) recommended mounting hole pattern for even number of contacts/row (shown for mounting side of pc board) .050 .002 typ [1.27] tolerance noncumulative position 2 position 1 .075 .003 typ [1.90] 2x ? .109 .002 [2.77] (see note 3) .025 .003 typ [0.64] c .002 e .225 .003 [5.72] .120 .003 [3.05] ? .025 .003 typ [0.64] edge of board .305 to .355 [7.75] [9.02] position 1 position 2
regulatory information appendix 3m electronic solutions division/interconnect europe appendix e1: european union rohs directive 2002/95/ec, restriction of the use of certain hazardous substances in electrical & electronic equipment, as amended by eu commission decision 2005/618/ec. this product is rohs compliant 2005/95/ec. rohs compliant 2005/95/ec means that the product or part (product) does not contain any of the substances in excess of the maximum concentration values in eu directive 2002/95/ec, as amended by commission decision 2005/618/ ec, unless the substance is in an application that is exempt under eu rohs. unless otherwise stated by 3m in writing, this information represents 3ms best knowledge and belief based upon information provided by third party suppliers to 3m. in the event any product is proven not to conform with 3ms regulatory information appendix, then 3ms entire liability and buyers exclusive remedy will be in accordance with the warranty stated below. appendix e2: european union rohs directive 2002/95/ec, restriction of the use of certain hazardous substances in electrical & electronic equipment, as amended by eu commission decision 2005/618/ec. this product contains lead in the compliant pin area in excess of the maximum concentration value allowed but is compliant by exemption under eu commission decision 2005/747/ec. rohs compliant 2005/95/ec means that the product or part (product) does not contain any of the substances in excess of the maximum concentration values in eu directive 2002/95/ec, as amended by commission decision 2005/618/ ec, unless the substance is in an application that is exempt under eu rohs. unless otherwise stated by 3m in writing, this information represents 3ms best knowledge and belief based upon information provided by third party suppliers to 3m. in the event any product is proven not to conform with 3ms regulatory information appendix, then 3ms entire liability and buyers exclusive remedy will be in accordance with the warranty stated below. appendix e3: european union rohs directive 2002/95/ec, restriction of the use of certain hazardous substances in electrical & electronic equipment as amended by commission decision 2005/618/ec. this product contains lead in the solder tail area in excess of the maximum concentration value allowed. unless otherwise stated by 3m in writing, this information represents 3ms best knowledge and belief based upon information provided by third party suppliers to 3m. in the event any product is proven not to conform with 3ms regulatory information appendix, then 3ms entire liability and buyers exclusive remedy will be in accordance with the warranty stated below. appendix e4: european union rohs directive 2002/95/ec, restriction of the use of certain hazardous substances in electrical & electronic equipment, as amended by eu commission decision 2005/618/ec. this product contains decabde in the insulating material in excess of the maximum concentration value allowed but is compliant by exemption under eu commission decision 2005/17/ec. rohs compliant 2005/95/ec means that the product or part (product) does not contain any of the substances in excess of the maximum concentration values in eu directive 2002/95/ec, as amended by commission decision 2005/618/ec, unless the substance is in an application that is exempt under eu rohs. unless otherwise stated by 3m in writing, this information represents 3ms best knowledge and belief based upon information provided by third party suppliers to 3m. in the event any product is proven not to conform with 3ms regulatory information appendix, then 3ms entire liability and buyers exclusive remedy will be in accordance with the warranty stated below. ria-2217-a
china appendix c1: china rohs electronic industry standard of the peoples republic of china, sj/t11363-2006, requirements for concentration limits for certain hazardous substances in electronic information products. this symbol, per marking for the control of pollution caused by electronic information products, sj/t11364-2006, means that the product or part does not contain any of the following substances in excess of the following maximum concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. unless otherwise stated by 3m in writing, this information represents 3ms best knowledge and belief based upon information provided by third party suppliers to 3m. in the event any product is proven not to conform with 3ms regulatory information appendix, then 3ms entire liability and buyers exclusive remedy will be in accordance with the warranty stated below. appendix c2: china rohs 2 0 electronic industry standard of the peoples republic of china, sj/t11363-2006, requirements for concentration limits for certain hazardous substances in electronic information products. this symbol, per marking for the control of pollution caused by electronic information products, sj/t11364-2006, means that the product or part does contain a substance, as detailed in the chart below, in excess of the following maximum concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. unless otherwise stated by 3m in writing, this information represents 3ms best knowledge and belief based upon information provided by third party suppliers to 3m. the numerical reference in the symbol above should not be construed as a representation regarding the products life or an extension of a product warranty. the product warranty is stated below. in the event any product is proven not to conform with 3ms regulatory information appendix, then 3ms entire liability and buyers exclusive remedy will be in accordance with the product warranty stated below. important notice all statements, technical information, and recommendations related to 3ms products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. before using this product, you must evaluate it and determine if it is suitable for your intended application. you assume all risks and liability associated with such use. any statements related to the product which are not contained in 3ms current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3m. warranty; limited remedy; limited liability. this product will be free from defects in material and manufacture for a period of ninety (90) days from the time of purchase. 3m makes no other warranties including, but not limited to, any implied warranty of merchantability or fitness for a particular purpose. if this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3ms option, to replace or repair the 3m product or refund the purchase price of the 3m product. except where prohibited by law, 3m will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3m product, regardless of the legal theory asserted. name and content of hazardous substances or elements 3 electronic solutions division 6801 river place blvd. austin, tx 78726-9000 800/225-5373 www.3m.com/interconnects ria-2217-a ? 3m 2007
|
